2020 Manac Extendable Flatbed

Extendable flatbed trailer for sale at Midco Sales.  The new Manac extendable flatbed trailer expands from 48′ to 80′ long.

This 48′ – 80′ extendable flatbed trailer has an apitong deck and steel crossmembers.

There is an air ride sliding suspension on this extendable trailer.

EXTENDABLE TRAILER DIMENSIONS

• Length: 48′ closed, 80′ open/extended
• Opening: 5′ increments in closed position
• Width: 102″, 97″ between side rails
• Height: Floor, approx 61 1/4″ high at front; 58″ at rear

COUPLING

• Coupler Plate: 5/16″, plug welded structure
• King Pin Location: 24″ from front
• Coupler Height: 49″

STRUCTURE

• Flanges: Female section, (exterior),  steel, 24″ high
• Flanges: Male section (interior), steel, 17 5/8″ high
• Web: 1/4″ plate in kingpin area and the remaining in 3/16″, steel
• Gooseneck: 12″ high with integrated nose ramp and 48″ straight behind extendable flatbed trailer kingpin
• Crossmembers: I beams, 4″ @ 3.64 lbs/ft, steel, 12″ center to center
• Floor: Apitong, 1 1/8″ thick shiplap finished, no preservative
• Floor Fastening: Two screws per board at each crossmember
• Side Rails: 6″ channel @ 8.2 lbs/ft
• Side Boxes: 3/16″ steel plate, 1 5/8″ x 3 5/8″ interior, 4″ high
• Rub Rails: steel
• Corners: Beveled
• Diagonal Braces: 2″ x 2″ x 3/16″ angles, welded in web and to a crossmember, located each side
• X Braces: Between main beams, full length, sheet metal with cutting holes at front and rear between mail main beams
• Locks: Air operated with a third glad hand at front of extendable trailer
• Rollers: 4, 2 on female sections of frames and 2 on male sections
• Spacers for Rub Rails: Double between side boxes

ENDS

• Front rail: formed steel
• Bumper: CMVSS 223-RIG approved. Uprights integrated with frames, 4″ x 4″ cross bar roll formed tubing at a max height of 22″ from under tubing to ground
• Bumper: Aluminum plate, bolted between bumper uprights to close rear
• Pull Plate: Pull plates between uprights of bumper
• Pockets: 2 welded pockets at front for removable headboard
• Rear Rail: 11″ high, steel, included 3 boxes at rear

ELECTRICAL

• Front Connector: 7 way (SAE J560), Phillips
• Electrical System: Shock proof lights, polycarbonate lenses
• Main System: Grote Ultra Blue LED, grounded to front connector, sealed beams
• Turn Signal: Sealed beams LED, one lamp including side marker and flasher, each side at middle point, amber
• Rear Add. Connector: 4 way

LANDING GEAR

• Sand shoes: 10″ x 11 1/2″
• Crank: Road side

SUSPENSION

• Hendrickson AAL-23K air ride slider, 50″ spread

AXLES

• LDA, 5 3/4″ diameter, 23,000 lb capacity

BRAKES

• Brakes: 16 1/2″ standard, H23 Hendrickson lining
• Slack Adjusters: Meritor, automatic, 28 splines
• Seals: Stemco
• Brake Chambers: TSE brake, Omnibrake

WHEELS & TIRES

• Wheels: 22.5 x 8.25 steel disc (10 holes)
• Tires: Continental 11R22.5 HT3 Eco-Plus, 14 ply

AIR SYSTEM

• Glad Hands: Fixed
• Air Valves: Meritor Wabco, ABS, 2 sensor 1 modulator
• Valve: Fast-brake kit
• Valve: Automatic blown down valve without control box

LOAD CONTROL

• Sliding Winch Tracks: Full length, LL extruded aluminum, road side
• Winches: Qty 12, zinc plated slider

ACCESSORIES

• Registration Holder (plastic)
• Retroflective Tapes: Conspicuity striping, gray and read each side

Complete this short online application to begin the financing process.  A Midco Sales representative will then contact you to obtain additional needed information.